Elliptical Cut-Outs vs Published Tests
Circles and ellipses in two AS4/3502 layups. The default d0 reads high here, which is the reason to fit your own.
Problem
Tan tested AS4/3502 strips with a circular hole or an elliptical opening across the load, with a/b = 2 and 5, in [0/90/±45]s and [0/902/0]s1. Here 2a is the opening's span across the load and 2b its extent along it. How well does the Open Hole tool's ellipse analysis predict the notched strength, at the default d0 and with d0 calibrated on one test per layup?
Not to scale. Drawn at a/b = 2. Dashed: the circle and the a/b = 5 opening with the same span 2a.
Inputs
| Material | AS4/3502 carbon/epoxy |
| Layups | [0/90/±45]s, [0/902/0]s |
| a/b | 1 (circle), 2, 5 |
| Opening span 2a | 0.4572 to 15.49 mm |
| Width W | 12.7 to 47.5 mm |
| Criterion | Fiber fracture in tension |
| d0, defaults | 1.5 mm |
| d0, calibrated, [0/90/±45]s | 0.78 mm |
| d0, calibrated, [0/902/0]s | 1.43 mm |
| Finite-width correction | On |
The paper gives the ply stiffness but no ply strengths, so the comparison is the ratio it tabulates: notched over unnotched strength, σN/σ0. The paper multiplied each measured stress by an isotropic finite-width factor. The test column below divides that back out (Heywood3 for circles, the paper's Fig. 6 for ellipses), so it is the measured gross ratio. The tool applies Tan's anisotropic factor instead4.
- Tool defaults: the point stress check out of the box, d0 = 1.5 mm.
- d0 calibrated on one test: d0 set per layup so the tool matches the 6.35 mm circular hole, then used unchanged on every other opening of that layup.
Predicted against test
One row per specimen, grouped by table and layup in the same order as the table below. The tick is the test, and each marker is one method's prediction. A marker right of the tick overpredicts the strength. The default markers use the tool's starting d0 of 1.5 mm, and the calibrated markers use a d0 set per layup so the 6.35 mm circular hole matches its test exactly, then reused on every other opening of that layup.
Left of the test tick: the prediction is below the test, the safe side.
Strength ratio σN/σ0: the failure stress with the opening over the failure stress without it. At 1 the opening costs no strength.
In words: 21 of the 28 default markers sit right of the test tick, on the unsafe side. For [0/90/±45]s the calibrated markers move left onto the tick, and for the larger openings they land on both sides of it.
Calibrate d0 yourself
Pick a layup, then move the slider to change d0. Every opening's marker moves with it. To calibrate, slide until the 6.35 mm circle sits on its test tick, then look at where the ellipses land. A larger d0 reads the stress further from the edge of the opening, where it is lower, so the predicted ratio goes up. Each layup needs its own d0, because d0 belongs to the laminate.
4 of 15 within 12% of the test, 0 on the safe side.
Left of the test tick: the prediction is below the test, the safe side.
Strength ratio σN/σ0: the failure stress with the opening over the failure stress without it. At 1 the opening costs no strength.
The slider moves in 0.05 mm steps, so the calibrated stop is 0.8 mm rather than the exact 0.78 mm.
Results
Gross notched over unnotched strength, σN/σ0, and the error against the test.
| Table | Layup | a/b | 2a (mm) | W (mm) | Test | Tool defaults | Error | Calibrated d0 | Error |
|---|---|---|---|---|---|---|---|---|---|
| Table 1 | [0/90/±45]s | 1 | 0.4572 | 12.7 | 0.934 | 0.974 | +4.3% | 0.933 | −0.1% |
| Table 1 | [0/90/±45]s | 1 | 2.54 | 12.7 | 0.627 | 0.771 | +23.0% | 0.697 | +11.2% |
| Table 1 | [0/90/±45]s | 1 | 6.35 | 25.4 | 0.503 | 0.640 | +27.2% | 0.503 | +0.0% |
| Table 1 | [0/90/±45]s | 1 | 7.62 | 25.4 | 0.468 | 0.579 | +23.7% | 0.456 | −2.6% |
| Table 1 | [0/90/±45]s | 1 | 10.41 | 34.8 | 0.448 | 0.514 | +14.7% | 0.415 | −7.4% |
| Table 1 | [0/90/±45]s | 1 | 15.49 | 47.5 | 0.390 | 0.438 | +12.3% | 0.369 | −5.4% |
| Table 1 | [0/90₂/0]s | 1 | 0.4572 | 12.7 | 0.999 | 0.975 | −2.4% | 0.973 | −2.6% |
| Table 1 | [0/90₂/0]s | 1 | 2.54 | 12.7 | 0.732 | 0.756 | +3.3% | 0.748 | +2.2% |
| Table 1 | [0/90₂/0]s | 1 | 6.35 | 25.4 | 0.584 | 0.590 | +1.0% | 0.584 | +0.0% |
| Table 1 | [0/90₂/0]s | 1 | 7.62 | 25.4 | 0.453 | 0.544 | +20.1% | 0.537 | +18.5% |
| Table 1 | [0/90₂/0]s | 1 | 15.49 | 47.5 | 0.522 | 0.432 | −17.2% | 0.425 | −18.6% |
| Table 2 | [0/90/±45]s | 2 | 2.54 | 12.7 | 0.614 | 0.765 | +24.6% | 0.663 | +8.0% |
| Table 2 | [0/90/±45]s | 2 | 6.35 | 25.4 | 0.522 | 0.605 | +15.9% | 0.516 | −1.1% |
| Table 2 | [0/90/±45]s | 2 | 7.62 | 25.4 | 0.500 | 0.559 | +11.8% | 0.477 | −4.6% |
| Table 2 | [0/90/±45]s | 2 | 10.16 | 34.8 | 0.410 | 0.524 | +27.8% | 0.430 | +4.9% |
| Table 2 | [0/90/±45]s | 2 | 15.24 | 47.5 | 0.426 | 0.463 | +8.7% | 0.352 | −17.4% |
| Table 2 | [0/90₂/0]s | 2 | 2.54 | 12.7 | 0.660 | 0.739 | +12.0% | 0.732 | +10.9% |
| Table 2 | [0/90₂/0]s | 2 | 6.35 | 25.4 | 0.527 | 0.552 | +4.7% | 0.543 | +3.0% |
| Table 2 | [0/90₂/0]s | 2 | 7.62 | 25.4 | 0.500 | 0.500 | +0.0% | 0.492 | −1.6% |
| Table 2 | [0/90₂/0]s | 2 | 10.16 | 34.8 | 0.385 | 0.460 | +19.5% | 0.455 | +18.2% |
| Table 2 | [0/90₂/0]s | 2 | 15.24 | 47.5 | 0.444 | 0.400 | −9.9% | 0.393 | −11.5% |
| Table 3 | [0/90/±45]s | 5 | 6.35 | 25.4 | 0.531 | 0.650 | +22.4% | 0.579 | +9.0% |
| Table 3 | [0/90/±45]s | 5 | 7.62 | 25.4 | 0.530 | 0.614 | +15.8% | 0.565 | +6.6% |
| Table 3 | [0/90/±45]s | 5 | 10.16 | 34.8 | 0.522 | 0.584 | +11.9% | 0.540 | +3.4% |
| Table 3 | [0/90/±45]s | 5 | 15.24 | 47.5 | 0.391 | 0.561 | +43.5% | 0.444 | +13.6% |
| Table 3 | [0/90₂/0]s | 5 | 7.62 | 25.4 | 0.548 | 0.492 | −10.2% | 0.484 | −11.7% |
| Table 3 | [0/90₂/0]s | 5 | 10.16 | 34.8 | 0.512 | 0.452 | −11.7% | 0.448 | −12.5% |
| Table 3 | [0/90₂/0]s | 5 | 15.24 | 47.5 | 0.453 | 0.449 | −0.9% | 0.456 | +0.7% |
Sources: Tan Tables 1 (circles), 2 (a/b = 2) and 3 (a/b = 5)1.
What it means
This time the defaults run high. For [0/90/±45]s every opening comes out above the test, by up to 43%, and for [0/902/0]s 6 of 13 do. The calibrated d0 for [0/90/±45]s is 0.78 mm, half the default, and with it the rows at W/2a of 4 or more land within 12%.
So 1.5 mm is not a safe default for every carbon laminate. It was conservative on the IM7-8552 coupons in Open-hole strength vs published tests and is unconservative on this AS4/3502. d0 is a calibration constant that depends on the material and the layup2. Fit it to open-hole coupons of your own material, run to ASTM D57665, before you size anything.
Related docs:
References
- Tan, S.C. (1987). Laminated composites containing an elliptical opening. II. Experiment and model modification. Journal of Composite Materials, 21, 949-968. (Tables 1-3, open-hole and elliptical-opening tests in AS4/3502; Table 5, lamina properties)
- Whitney, J.M. & Nuismer, R.J. (1974). Stress fracture criteria for laminated composites containing stress concentrations. Journal of Composite Materials, 8(3), 253-265. doi:10.1177/002199837400800303
- Heywood, R.B. (1952). Designing by Photoelasticity. Chapman & Hall. (Finite-width factor for a circular hole in an isotropic plate)
- Tan, S.C. (1988). Finite-width correction factors for anisotropic plate containing a central opening. Journal of Composite Materials, 22(11), 1080-1097. doi:10.1177/002199838802201105
- ASTM D5766/D5766M. Standard Test Method for Open-Hole Tensile Strength of Polymer Matrix Composite Laminates. ASTM International.