Open the calculatorOpen the calculator

Ply Stresses in a [±45]s Laminate under Tension

Pull a ±45 laminate along x and each ply ends up in shear. Worked from the A matrix to the safety factor.

Problem

A [45/−45]s laminate of T300/5208 carbon/epoxy carries Nx = 100 N/mm of tension, with no other load. Find the stresses in each ply along and across its fibers, and the Tsai-Wu safety factor.

NxNxxySeen from above1: +45°2: −45°3: −45°4: +45°Edge-on, ply 1 on top

Ply 1 on top: 45°, −45°, −45°, 45°, 0.125 mm each, 0.5 mm in total. Angles run counterclockwise from x.

Inputs

Layup[45/−45]s, ply 1 on top
Ply thickness0.125 mm
E1181000 MPa
E210300 MPa
G127170 MPa
ν120.28
S1t / S1c1500 / 1500 MPa
S2t / S2c40 / 246 MPa
S1268 MPa
Nx100 N/mm
Ny, Nxy, M0

Change the ply angle

Same material, same Nx, any angle from 0 to 90°. The curves show the +θ ply; the −θ ply has the same σ1 and σ2 and the opposite τ12.

-150-5050150250Stress (MPa)SF = 102468Tsai-Wu SF0153045607590Ply angle θ (°)
σ1σ2τ12Tsai-Wu SF, +θ ply

[45/−45]s under Nx = 100 N/mm

Plyσ1σ2τ12SF
+45°186.613.38−1000.6161
−45°186.613.381000.6161

Stresses in MPa, in the fiber axes of each ply.

At θ = 45° the +θ ply carries σ1 = 187, σ2 = 13.4 and τ12 = −100 MPa. Tsai-Wu says the plies fail before 100 N/mm, at about 61.6 N/mm.

σ1 + σ2 stays at 200 MPa at every angle, which is Nx spread over the 0.5 mm thickness. The angle only decides how that stress splits between the fiber and the matrix, and how much shear comes with it.

Results

Each ply carries
τ12 = ±100 MPa
σ1 = 186.6, σ2 = 13.38 MPa
Tsai-Wu says
First-ply failure at 61.6 N/mm
SF = 0.6161 at 100 N/mm

The shear stress in the fiber axes is the same size in every ply, 100 MPa, and it fails the laminate before the 100 N/mm load is reached.

Step 1. The A matrix

Rotate each ply's stiffness Q into the laminate axes (Q̄) and sum over the plies, weighted by thickness. The stack is symmetric, so B = 0, and balanced, so A16 = A26 = 0. In N/mm:

A=∑kQˉktk=[28328.921158.9021158.928328.900023295.4]\mathbf{A} = \sum_k \bar{Q}_k t_k = \begin{bmatrix} 28328.9 & 21158.9 & 0 \\ 21158.9 & 28328.9 & 0 \\ 0 & 0 & 23295.4 \end{bmatrix}
A=∑kQˉktk=[1617621208200120820161762000133020]\mathbf{A} = \sum_k \bar{Q}_k t_k = \begin{bmatrix} 161762 & 120820 & 0 \\ 120820 & 161762 & 0 \\ 0 & 0 & 133020 \end{bmatrix}

Step 2. Midplane strains

With B = 0 the membrane problem stands alone. Solve A ε0 = N:

{εx0εy0γxy0}=A−1{10000}={7984−59630}με\begin{Bmatrix} \varepsilon_x^0 \\ \varepsilon_y^0 \\ \gamma_{xy}^0 \end{Bmatrix} = \mathbf{A}^{-1} \begin{Bmatrix} 100 \\ 0 \\ 0 \end{Bmatrix} = \begin{Bmatrix} 7984 \\ -5963 \\ 0 \end{Bmatrix} \mu\varepsilon
{εx0εy0γxy0}=A−1{57100}={7984−59630}με\begin{Bmatrix} \varepsilon_x^0 \\ \varepsilon_y^0 \\ \gamma_{xy}^0 \end{Bmatrix} = \mathbf{A}^{-1} \begin{Bmatrix} 571 \\ 0 \\ 0 \end{Bmatrix} = \begin{Bmatrix} 7984 \\ -5963 \\ 0 \end{Bmatrix} \mu\varepsilon

There is no curvature, so every ply sees these same strains. The laminate narrows by 0.747 times its stretch: that ratio is νxy, and it is large because the ±45 plies scissor.

Step 3. Rotate into the fiber axes

For the +45° ply, with c = cos θ and s = sin θ:

ε1=c2εx+s2εy+cs γxy=1010 μεε2=s2εx+c2εy−cs γxy=1010 μεγ12=2cs (εy−εx)+(c2−s2) γxy=−13950 με\begin{aligned} \varepsilon_1 &= c^2 \varepsilon_x + s^2 \varepsilon_y + cs\, \gamma_{xy} = 1010\ \mu\varepsilon \\ \varepsilon_2 &= s^2 \varepsilon_x + c^2 \varepsilon_y - cs\, \gamma_{xy} = 1010\ \mu\varepsilon \\ \gamma_{12} &= 2cs\,(\varepsilon_y - \varepsilon_x) + (c^2 - s^2)\, \gamma_{xy} = -13950\ \mu\varepsilon \end{aligned}

At 45° the fiber and transverse strains are equal, and the shear strain is the difference of εx and εy. In the −45° ply γ12 flips sign.

Step 4. Ply stresses

Multiply by the ply stiffness in its own axes, Q11 = 181811, Q12 = 2896.92, Q22 = 10346.2 and Q66 = 7170 MPa:

σ1=Q11ε1+Q12ε2=186.62 MPaσ2=Q12ε1+Q22ε2=13.3802 MPaτ12=Q66 γ12=−100 MPa\begin{aligned} \sigma_1 &= Q_{11} \varepsilon_1 + Q_{12} \varepsilon_2 = 186.62\ \text{MPa} \\ \sigma_2 &= Q_{12} \varepsilon_1 + Q_{22} \varepsilon_2 = 13.3802\ \text{MPa} \\ \tau_{12} &= Q_{66}\, \gamma_{12} = -100\ \text{MPa} \end{aligned}
σ1=Q11ε1+Q12ε2=27.0669 ksiσ2=Q12ε1+Q22ε2=1.94063 ksiτ12=Q66 γ12=−14.5038 ksi\begin{aligned} \sigma_1 &= Q_{11} \varepsilon_1 + Q_{12} \varepsilon_2 = 27.0669\ \text{ksi} \\ \sigma_2 &= Q_{12} \varepsilon_1 + Q_{22} \varepsilon_2 = 1.94063\ \text{ksi} \\ \tau_{12} &= Q_{66}\, \gamma_{12} = -14.5038\ \text{ksi} \end{aligned}

Step 5. Tsai-Wu safety factor

Scale the stresses by SF until the Tsai-Wu index reaches 1. The linear terms L = F1σ1 + F2σ2 grow with SF, the quadratic terms Q with SF2:

Q SF2+L SF=1,Q=2.18, L=0.2801⇒SF=0.6161Q\, \mathrm{SF}^2 + L\, \mathrm{SF} = 1, \quad Q = 2.18,\ L = 0.2801 \quad \Rightarrow \quad \mathrm{SF} = 0.6161

All four plies, stresses in MPa:

PliesAngleε1 (µε)ε2 (µε)γ12 (µε)σ1σ2τ12Tsai-Wu SF
1, 445°10101010−13950186.613.38−1000.6161
2, 3−45°1010101013950186.613.381000.6161

What it means

Under axial load a ±45 laminate works through its matrix. At 45° the fibers carry σ1 = 186.6 MPa, about 12% of their strength. The shear, 100 MPa against S12 = 68 MPa, is what fails the ply.

Move θ toward 0° and the fibers line up with the load: shear drops away and the safety factor climbs to 7.5. Move it toward 90° and σ2 takes over, against a transverse tensile strength of only 40 MPa, so the safety factor falls to 0.2. Use ±45 plies for shear and torsion stiffness, and 0° plies for the axial load.

First-ply failure is where matrix cracking starts, not where the laminate breaks. Past it the cracked plies lose transverse and shear stiffness and the load moves to the fibers.

Related docs:

References

  1. Jones, R.M., Mechanics of Composite Materials, 2nd Ed., Taylor & Francis, 1999.
Open in calculator

Build [45/−45]s in the free laminate calculator and compare its A matrix with step 1. It opens with its own default layup, so enter the four plies by hand.

Open the laminate calculator
Written by Rick Schrijver
Share