• Docs
  • Laminate Analysis
Open the toolOpen the tool

Maximum Strain Failure Criterion

The maximum strain criterion for a composite ply: strains from the compliance, allowable strains from the strengths, the safety factor, and one ply worked by hand.

What the maximum strain criterion predicts

Maximum strain runs the checks of maximum stress on the ply strains instead of the stresses1. ε1 along the fibers, ε2 across them and the shear strain γ12 each go against their own allowable. The ply fails when any ratio reaches 1, and that ratio names the mode.

The strains come from the ply compliance, so Poisson coupling enters. A transverse stress changes the fiber-direction strain and the other way round. That is the only interaction the criterion has, and it is indirect. In stress space the envelope is a parallelogram rather than the rectangle of maximum stress.

Maximum strain belongs to the no-interaction family. The cards draw each family's failure envelope for the same ply in the σ1-σ2 plane, with no shear.

σ1σ2
No interaction
Max stressMax strain

Each stress, or each strain, is checked against its own limit. Max stress draws a box with sharp corners. Max strain draws a slanted box, because the Poisson effect puts some σ1 into ε2.

σ1σ2
Quadratic interaction
Tsai-HillTsai-Wu

All stresses go into one quadratic expression. The envelope is one smooth, ellipse-like curve, and it does not say whether the fiber or the matrix failed.

σ1σ2
Failure modes
HashinPuck

Fiber and matrix failure get separate checks. The envelope is pieced together from one curve or line per mode.

Also in this family, not drawn: Cuntze, Sun, Edge.

When to use maximum strain

Use it when your allowables are strain values, or when a fiber-direction strain limit is the requirement. It needs the elastic properties in the check itself, not only in the CLT step before it. For combined loading, run an interactive criterion such as Tsai-Wu next to it.

Maximum strain formula

The ply strains follow from the stresses through the compliance1:

ε1=σ1E1−ν12E1σ2\varepsilon_1 = \frac{\sigma_1}{E_1} - \frac{\nu_{12}}{E_1}\sigma_2
ε2=σ2E2−ν21E2σ1\varepsilon_2 = \frac{\sigma_2}{E_2} - \frac{\nu_{21}}{E_2}\sigma_1
γ12=τ12G12\gamma_{12} = \frac{\tau_{12}}{G_{12}}

and the ply fails when any of these holds:

ε1ε1T≥1  or  −ε1ε1C≥1\frac{\varepsilon_1}{\varepsilon_{1T}} \ge 1 \;\text{or}\; \frac{-\varepsilon_1}{\varepsilon_{1C}} \ge 1
ε2ε2T≥1  or  −ε2ε2C≥1\frac{\varepsilon_2}{\varepsilon_{2T}} \ge 1 \;\text{or}\; \frac{-\varepsilon_2}{\varepsilon_{2C}} \ge 1
∣γ12∣γ12u≥1\frac{|\gamma_{12}|}{\gamma_{12u}} \ge 1

ν21 = ν12E2/E1. The dashboard derives the allowable strains from the strengths and moduli: ε1T = S1t/E1, ε1C = S1c/E1, ε2T = S2t/E2, ε2C = S2c/E2 and γ12u = S12/G12. With those allowables the shear check is the same as in maximum stress, and the normal checks differ from it by the Poisson terms.

Failure index and safety factor

The failure index is the largest of the five strain ratios, and the safety factor is SF = 1/FI. The strains are linear in the stresses, so FI scales with the load. The overview covers safety factors and margins for all criteria.

Worked example: one ply

Take the +45° ply of the quasi-isotropic laminate example. It is T300/5208 carbon/epoxy, with E1 = 181000 MPa, E2 = 10300 MPa, G12 = 7170 MPa and ν12 = 0.28. Its stresses are σ1 = −93.31 MPa, σ2 = −6.69 MPa and τ12 = −40.01 MPa. Both normal strains come out compressive, so the compressive allowables apply.

StrainAllowableRatio
Fiber compression, ε1−505.2 µε8287 µε0.06096
Matrix compression, ε2−505.2 µε23880 µε0.02115
Shear, γ12−5580 µε9484 µε0.5884

Shear governs, with FI = 0.5884 and SF = 1.7, the same as maximum stress for this ply. γ12/γ12u reduces to |τ12|/S12, so the shear check cannot differ. The fiber and transverse ratios do differ from their stress counterparts (0.06096 against 0.06221 along the fibers), because Poisson coupling moves each strain.

Limitations

  • The only interaction is Poisson coupling. Shear and transverse stress still do not add up, so it can be non-conservative under combined loading.
  • Strain allowables derived from strengths assume the ply stays linear to failure. Where a test gives a measured allowable, enter that instead.
  • It predicts first-ply failure only. What the laminate carries after that is a progressive failure question.

Beyond the Live Calculator

The free calculator does not run max strain. The app runs it with eight other criteria on every ply of a laminate, with first ply failure and progressive failure.

Create free account
app.abdcomposites.com
CLIP loops

Frequently asked questions

It checks each ply strain against its own allowable: ε1 along the fibers, ε2 across them and the shear strain γ12. The ply fails when any ratio reaches 1.

References

  1. Jones, R.M., Mechanics of Composite Materials, 2nd Ed., Taylor & Francis, 1999.
Written by Rick Schrijver
Share